• 5 sizes: 450/600/1000/1600/2000 m³/ h.
• 2 models:
  • R: blowing on the right of the control box,
  • L: blowing on the left.
• Online duct connection configuration.
• Communicating TAC5 regulation:
  • Modbus RTU- RS485,
  • Modbus TCP / IP,
  • KNX TP,
  • Wifi: smartphone application, tablet,
  • Ethernet: PC application,
  • BACnet gateway.

• Box with self-supporting structure in galvanized steel.
• Double skin panels 30 mm thick with rock wool insulation (Euroclass A1), thermal conductivity 0.035W / (mk).
• Polyester-type prepainted steel exterior finish (5µm primer +
  20 µm polyester).
  • Interior finish in galvanized steel (5μm primary + 20μm polyester).
• Classification EN 1886 D1 / L3 / F8 / T3 / TB2.
• Airtightness according to standard EN 13141-7:
  • internal leakage: class 1; external leak: class 2.
• Access to filters and exchanger from below.
• Drip tray equipped with a condensate drain pump (factory connected) and drain pipe (Ø 10 mm).
• By-pass 100%, controlled by a proportional servomotor, used for free cooling and the antifreeze strategy of the exchanger.
• Supplied with 4 mounted / wired probes.

• Galvanized steel double inlet fan.
• Low consumption, direct current, 230 V single-phase ECM motor. Electronic thermal protection - manual reset.

• High efficiency air / air countercurrent heat exchanger made of “seawater resistant” aluminum for an operating temperature of up to 80 ° C. Thermal efficiency up to 92%.

• On delivery G4 filters (coarse 65%) during extraction. G4 (coarse 65%) to the fresh air intake. Possibility, as an accessory, to replace the G4 filter (coarse 65%) by an F7 filter (ePM1 60%) air intake by
  1 Kit G4 / F7 or replace G4 filters (coarse 65%) by M5 filters (ePM10 50%) at extraction and F7 (ePM1 60%) on fresh air.

• On delivery, M5 filters (ePM10 50%) extraction and M5 (ePM10 50%) New air. Possibility of replacing the M5 filter (ePM10 50%) by an F7 filter (ePM1 60%) to the fresh air intake (Kit M5 / F7) as an accessory.
• Filters are easily accessible from underneath the unit.

• Complete regulation allowing 3 operating modes:

• The operation of the exhaust fan is slaved to the supply fan. Its flow rate corresponds to a percentage of the flow rate of the supply fan (generally 100%).
• Programmable and controllable regulation from the remote control.

• HMI TACtouch 4.3 "touchscreen, IP20 for parameter setting, control, visualization.
• SAT3, circuit with 2 relays for:
  • Pressure alarm signaling and "fan on" signal and / or circulator control and bypass status.
• SAT MODBUS, allows the options below:
  • Connection to a GRC (remote control with touch screen),
  • Communication in Modbus RTU - Control and visualization via a BMS.
• SAT ETHERNET:
  • Communication with Modbus TCP / IP protocol in Ethernet network on 10 BASE T twisted pair. Allows communication with a BMS or interfacing with the EOLE4HR application for smartphone, tablet and PC (Android, IOS or Windows 7/8/10) .
• SAT BA / KW kit allows the control of the external batteries from the TAC5 regulation.
• SAT WIFI:
  • Communication with Modbus TCP / IP protocol by WIFI. Allows communication with a BMS or interfacing with the EOLE4HR application for smartphone, tablet and PC (Android, IOS or Windows 7/8/10).

• Supplied fully pre-wired with regulation.
• Accepts a temperature of -20 ° C at the intake for an internal temperature of 20 ° C, without risk of the exchanger freezing.
• Includes: static relay for modulating the heating power, temperature probe, thermal protection with automatic reset (75 ° C) and manual reset (100 ° C).

CBAE - box for external hot water or chilled water coil

• Box with aluminum profile structure and 30 mm thick double skin panel, with thermal insulation made from rock wool (Euroclass A1), thermal conductivity 0.035W / (mk)

Batteries for CBAE:

• BAEC: hot water coil 2 or 4 rows,
• BAEF: 4-row cold water coil equipped with a condensate collection tray and an evacuation pump. The batteries can be optionally fitted with a V3V / servomotor / SAT BA / KW kit comprising:
  • the SAT BA / KW kit for connection to the TAC5 regulation with 2 temperature probes, one of which is a contact for the coil's antifreeze protection + 1 motorized 3V valve.
• BADX: direct expansion coil
  • 4-row coil, for R410 fluid, equipped with a condensate pan and an evacuation pump.
  • Battery delivered without regulation